Tag Archives: Vans

The LMS Van

The LMS, as the largest of the four companies, was the one which contributed most to the ‘pool’ of wagons controlled by the RCH and which of course eventually came into BR ownership.  Vast quantities were built to various designs, no doubt causing some degree of confusion at first glance.  As is often the case though, with a little analysis it is evident that a very large percentage of them had a distinct familial resemblance, with the corrugated ends that had first been used back in the 1920s and being essentially to one standard body shape, which also accommodated a post-war change to plywood body sheeting instead of planking.  The last batches to LMS orders actually appeared with BR numbers, and many lasted in significant numbers into the mid-1960s and hence the diesel era.

The vans of the  SR and LNER have recently been quite well catered for out of the box, together with Parkside’s retooling of its post-war LNER plywood van.  The old Mainline moulding for the GW Mink is now middle aged but still acceptable, and this leaves a gap that is surely ripe for RTR exploitation.  For now though, there are three principal LMS-pattern van models available which can round out the picture for a BR van fleet.   These are the venerable Ratio 591/5091 kit, a very similar one-piece moulding in the Airfix RTR range and Parkside’s PC42 kit, which although intended as a BR fruit van to a plywood LMS-inspired design, can be used to represent ordinary vans built by both the LMS and BR.  Contemporary with the Airfix model, an equivalent model appeared in Mainline’s range, easily recognisable by its crude working sliding door;  at some point this was retooled to lose the gimmick, but retained its squat appearance.  To be honest it’s best avoided, as the ex-Airfix moulding is way superior, still available from Dapol and secondhand examples are not rare.

The Ratio kit dates back some forty years now, an all-time classic wagon kit in my opinion, and is still a hard act to follow.  The assembled kit captures the look and proportions beautifully, particularly the characteristic corrugated end and the shape and size of the vent hoods.  Over 20,000 vans were built to the diagrams that it covers  (LMS D1891/1897/1978/2039), so it’s a model that can easily be justified on any layout from the mid-1930s to around 1970.

The one below is in progress, awaiting the ‘metalwork’ stage where it will acquire buffers and tiebars.  Most of these vans acquired additional diagonal strapping during BR days, and this has been represented with plastic strip.  The sharp eyed will see that I didn’t get this positioned spot-on the first time,  which irks me, but it’ll come right once it’s painted and weathered.  I’m also deliberating over providing boltheads on the additional strapping, it may provide an excursion for my Archers rivet transfers.

Although in shadow in this shot (showery in E Yorks today, indoor photography only), it also sits on a Parkside 10ft wheelbase underframe, which I used in order to give a bit of variety and portray a van with BR-pattern axleguards and plate axleboxes.  You can normally do this sort of thing with different chassis kit parts, although a little thought can be needed to accommodate the disparate brakegear parts.  The Parkside floor though fits as if it was made for the job. A second Ratio kit is in build, this one being altered to an early D1891 van with vertically planked doors, and will join a third van that’s been left as intended, although it will acquire a clasp braked, J-hanger suspended chassis courtesy of Parkside’s PA16 parts.  Not that there’s much wrong with the Ratio underframe as it comes, it can be used to represent  a van as vac fitted by BR or (by omitting one set of pushrods, the ones on the side without the Morton clutch), an  unfitted van as originally built.  Other than the rather thick moulding feeds, as visible here on those end sprues, the crispness of these mouldings could easily be mistaken for a modern Parkside kit:

Below is an example of the Airfix RTR  offering; one important recognition feature it depicts is that whereas pukka LMS vans have channel section vertical uprights, BR builds ( diagram 1/204)  have a different section.  The diagonal stanchions are also doubled at points. All of the BR examples were built in vac fitted form, again this is catered for by the appropriate parts from Parkside’s useful PA16 chassis kit:

A bit of added bolthead detail appears on that top board, and also seen here is a very distressed example of a trader’s label, of which more anon…

The Parkside PC42 van is a very rare thing, a model in their range which doesn’t convincingly capture the prototype.  This is because it mistakenly uses a roof profile more akin to the BR standard van.  It is possible to reprofile the top edge of the ends, but this still leaves the vent hood position looking a bit odd, so the solution I chose was to use the ends and roof from the aforementioned Ratio kit, which sets everything up right from the off and immediately shows how far out the sides are .  If you’re frugal in outlook, by the way, there’s no need to shell out for a brand new kit for this purpose as indifferently-built examples can be picked up for a few quid at swapmeets and can with care be dismantled for spares.

My part-finished model here shows the extra 40 thou or so that was inserted  between the body top and the roof.  Again a PA16 chassis provides the undergear, for what will be a BR built example of diagram 1/200. Well one day it will, although I’d vainly add that this is a ‘library’ photo and since it was taken, it has progressed slightly; label boards have been added, together with the boltheads along that upper join in the corrugated end.  LMS vans didn’t always have these details, and so I might just yet do another one as a relative quickie to pair with it.  It’s probably worth pointing out as well that the LMS ply vans, unlike the planked variants above, did have the pattern of upright shown here (D2108), although a small batch to D2097 didn’t have the diagonals and don’t generally seem to have acquired them later.

Other LMS vans that should be mentioned are an all-plywood wartime van, plus some to LNER and SR designs that were delivered during WW2.  There’s also the odd earlier van that can form part of the ’60s scene, and one or two of these might be along in due course.

Useful references:  An Illustrated History of LMS Wagons vol. 1, R J Essery; article in MRJ 205 by Mick Moore; plus the many photographic references provided by Paul Bartlett’s website, David Larkin’s books for Santona and Kestrel, and the late Geoff Gamble’s Cheona volumes.


Filed under Vans, Wagon kits, Wagon weathering